This modification is something I came up with after struggling to get a reasonable range from my Nokia N82 to my computer in another room. The victim was a $8 USB Bluetooth dongle, with a usable range of about 10 metres (less through walls). Being a radio ham, I am familiar with antennas, and know how critical it is to get the CORRECT antenna length, if your signal is going to be efficient. I was surprised to find other 'range extender' mods on the net, which did not mention this important fact! (One site had someone who had attached a 'foot long piece of wire' onto his USB dongle and was wondering why it didn't work very well!!!) There is a recognised formula for calculating antenna length/frequency, which is (without going into detail) 300/frequency - i.e. 300/150(MHz) will give you 2 metres.
Find many great new & used options and get the best deals for Sena Ud100 Long Range Bluetooth 4.0 Class1 USB Adapter at the best online prices at eBay! Free shipping for many products! LM540 - Long Range Bluetooth 2.1+EDR USB Adapter this product is being replaced with LM1010 Long Range Class 1 Bluetooth USB Adapter with SMA Antenna Connector The LM540 - Long Range Bluetooth 2.1 + EDR USB Adapter is a qualified against the Bluetooth BT2.1 + EDR Standard and is available with or without support for the IVT Bluetooth software stack for use with a Windows PC or 'Other O/S.
As Bluetooth devices work at frequencies of around 2450MHz, the formula will give you an antenna length of +/- 12cm. This figure then has to be divided by 4 to give us a quarter wave antenna, which will be 30mm in length - THIS LENGTH IS CRITICAL!!!
25mm or 35mm will just make it less efficient (Lower range). Your old CB antenna WILL NOT WORK! So - if you are happy to try something (at your own risk), and want to get a significant increase in usable range for you dongle, go to the next step, but remember, the end result doesn't look pretty, but performs brilliantly! OK, so now we're inside, and you should be looking at a small PCB (printed circuit board).
Having second thoughts now? If you aren't confident with a soldering iron, simply pop everything back together again, and forget this mod. If you are ok to continue (a small glass of whiskey will help!), then we'll move to the next stage. On the side of the PCB with the 2 chips and a 13MHz crystal, you will see a hook-shaped silver line at the top of the board (I've marked this in YELLOW on the picture). This is the antenna which you're using at the moment. Now you can see why the range is somewhat limited!!
![Bluetooth usb adapter class 1 long range reviews Bluetooth usb adapter class 1 long range reviews](/uploads/1/2/5/3/125386448/422413823.jpg)
Ok, bite the bullet, because this has got to come out, and you're gonna remove it. It is easier than you think, all you have to do is find a sharp utility/hobby knife, and simply SCRAPE IT OFF THE PCB. Be very careful to scrape towards the edges of the PCB to avoid damaging the other smd components on the board.VERY IMPORTANT. leave enough of the old antenna on the board to give you something to solder you new antenna onto. I've marked the STOP area in RED on the pic.
DO NOT remove all of the old antenna (leave about 3-5mm). Right - The old antenna is now removed.
The Yellow shows where it was, and now you should have a small left-over piece of the old antenna to give you something to attach (solder) your new antenna onto. For the new antenna, I used a 30mm (CRITICAL!!!) piece of rigid copper wire (earth wire etc), which gives a better bandwidth, but is also liable to pull the old antenna track away from the PCB if soldered directly onto the track. For this reason, I made a small hole in the PCB, using a small watchmakers' screwdriver (you can use a dremmel or 1mm drill bit). Whatever method you use, make sure you support the PCB on a firm surface, to avoid stressing the board while you're making the hole. The antenna is then threaded through the PCB from the other side. Now it gets tricky, because you cannot hold the wire while you're soldering it to the track (it's too hot), so you need to find a way to support the board while you're soldering it. Also remember to 'tin' the wire, before you solder it (it gives a better connection, and also solders quicker so you don't overheat the other components).
When soldered in place, the antenna will now stand up vertically from the PCB, and is likely to come unattached, or break the old track (antenna), if you try to play with it (bend it straight etc), so LEAVE IT ALONE! At this point, it would be wise to check that you have soldered it correctly, and have a good joint (connection).
HOLDING THE PCB BY THE EDGES, plug it into your USB socket (I use a short extension lead), and see if the LED lights up, and the device is recognised. Don't touch the components while you're plugging it in, because you are almost certain to short something out, and totally wreck your new improved dongle. You should already have a good idea what range you had before, and should now be able to see a significant increase in the operating range. If you live in a well populated area, do a device scan to see if any phones etc are in range (you'll be surprised). If all is ok, then you have another problem - how do I get it back into the plastic case? I just used my still hot soldering iron to make a hole in the case for the antenna to poke through (I never said it was going to be pretty!!) The hole should be in the plastic case which does NOT have writing on it, and is located level with the little plastic 'ledge' inside, where the PCB sits - on the opposite side to the hole for the 'dummy' antenna.
If you don't get the hole position quite right, DO NOT try to bend the antenna to fit through, make the hole bigger - you will avoid ripping the track up on the board. As you can see from my picture, I got the position wrong, so just made a bigger hole. (ugly, but practical). With the case back in place, you're now the proud owner of probably the worlds ugliest looking USB Bluetooth dongle!
![Range Range](http://sc01.alicdn.com/kf/HTB1hpnTKVXXXXXhXFXXq6xXFXXX4/Long-Range-Rate-Bluetooth-USB-Adapter.jpg_350x350.jpg)
BUT on the positive side, you now have a Bluetooth dongle which will outperform anything for less than $50! The range of mine is now a lot more than the 10-15 metres I got previously, with every room in the house being in range, and a 'line of sight' range in excess of 200 metres! You could, of course, add a parabolic reflector (aluminium wok etc) to get ranges of more than 1 or 2km, but for practicality, I find the range more than adequate for my needs. The same mod can also be applied to WiFi dongles, with similar increase in usable range, but I don't want to experiment with my $35 WiFi adaptor just at the moment (I'm poor!) Also remember that Bluetooth operates a 'handshake' protocol, where it needs to recieve a signal, as well as transmit it, so if your phone has a naff bluetooth system, then don't expect to get much increase in range. For sniffing out other devices in the neighbourhood though, you should find signals you couldn't detect before.
There are other antenna designs which you could also try (co-linear etc) which will improve things even more, but this design is a quick and cheap (free?) method to get the most from a cheap Bluetooth device. Apologies for the terrible soldering in the picture, but I used a soldering gun for the job (yikes).
Any comments or questions can be sent to me at: [email protected] Good luck, and thanks for viewing. I always say, 'only a question unasked, is dumb', so no worries. Sorry for the late reply (2 years!), and no doubt you already know the answer. Anyway, the 360 degree radiated pattern is formed around an antenna in a 'doughnut' configuration, and not like a sphere or ball surrounding the antenna. Most of the signal is generated within this 'doughnut', with very little at the end of the antenna (the signal doesn't go up or down, only around). If the antenna is horizontally polarized (laid down), the least amount of signal will be wherever you 'point' the antenna.
The signal degradation between a vertical and horizontal antenna is also a key factor, so if the TX antenna is vertical, then the RX antenna should also be vertical, or visa-versa. Hope that cleared it up. Well whaddya know.it works!
Amazing what a little theory does. I just tried it on a cheapy $2 ebay dongle that wouldn't get more than 1 metre range before the signal started to break up and crackle. Now I've got about 5 metres!
I did accidentally pull up the remainder of the trace but my solder joint held. A little dab of hot glue should hold it firm.Also, don't bother picking out all the existing antenna, simply make a wide cut in front of where you will solder and the antenna is not connected anymore.The original was 45mm longThanks Josh.
The whole concept of this instructable is based on modifying the ANTENNA, leaving the actual power settings of the device unchanged. Your phone/PDA etc does not need to be altered in any way, as the antenna on the dongle does all the work, enhancing both the transmitted and RECEIVED signals. Bluetooth relies on a 2-way communication between devices, and is configured to work when a 'handshake' with a device has been established. Since I wrote this article, there have been many advances in bluetooth technology and the modification of the new devices is easy, with a simple firmware hack/update changing power levels of the TX. That still leaves you with the problem of receiving a low power device, and an antenna is the only solution, short of modding the device itself.
In any case, bluetooth was and still is only a SHORT RANGE communication medium, but I enjoy pushing the limits!
Designed to be fully compatible with Bluetooth v4.0 Standard and BT2.0 BT2.1 EDR BT3.0. Dual Mode HCI Adapter supporting Bluetooth v3.0 and Bluetooth Low Energy.This is a very small form factor and high performance adapter which allows you to connect up to 7 Bluetooth devices simultaneously.The adapter integrates high performance Bluetooth Radio, Baseband, Link Manager, Host Controller Interface and is distributed with Widcomm Software which offers a huge range of Bluetooth profiles for variety of connectivity applications. The adapter is ideally suited for Bluetooth connectivity to serial adapter, laptops, PC, Bluetooth Low Energy Devices, Mono and stereo headsets.Note: These items are buk packed. Please if you need full retail packaging. BT 4.0 dual mode (Standard Bluetooth and Bluetooth Low Energy)2.
Support Maximum Asynchronous Data Rate = 3 Mbps3. Supports Bluetooth Low Energy4. Provide data access via USB 2.0 interface5. Small Form Factor 19.47 x 16 x 8.1 mm6.
Class 1 adapter with upto 110 m in open space7. Wide range of Bluetooth profiles supported (like HF, A2DP, OPP, FTP, DUN, PAN, SPP, HCRP, HID, SYNC, BTLE profiles etc)8. Eliminates the need of cable between your computer and other Bluetooth Devices Specifications ManufacturerLM Technologies LtdChipsetBroadcom BCM20702Power ClassificationClass 1Adapter TypeUSB AdapterInterfaceUSB 2.0Bluetooth SpecificationBluetooth v 4.0, backward compatible with BT3.0/2.1/2.0 + EDRFrequency2.402 - 2.480 MHz ISM BandTemperature Range-30°C to +85°CData Transfer Rates3 Mbps enhanced data rate 250 Kbps Low Energy mode data rateRangeMaximum 110 m in open spaceTx PowerClass 1 ( +8 dBm)Rx Sensitivity.